Test

Description

Quantity Required

Waterstops and Gate Seals

CRD-C 513

Rubber Waterstop and Gate Seals,

a. Full evaluation, initial 60 m (200 lineal ft)

b. Tensile strength and elongation, each additional

60 m (200 ft)

c. Job-made splices

1.2 m (4 ft)

1.2 m (4 ft)

1 sample

CRD-C 572

Polyvinyl Chloride Waterstops

a. Full evaluation, initial 60 m (200 lineal ft)

b. Tensile strength and elongation, each additional

60 m (200 ft)

c. Job-made splices

1.2 m (4 ft)

1.2 m (4 ft)

1 sample

Joint Fillers

CRD-C 507

(TT-C-00598C)*

CRD-C 506

(TT-S-00227E)*

CRD-C 541

(TT-S-230a)*

CRD-C 542

(TT-S-001543A)*

CRD-C 543

(TT-S-001657)*

All Caulking and Sealing Compounds, for large bulk

containers, composite sample from top, middle, &

bottom

For small lots of material, Federal Test Method

Standard No. 141

1 L (1 qt)

Method 1021

CRD-C 508

(ASTM D 1751)

Preformed Expansion Joint Filler (Non-extruding and Resilient Bituminous Types)(per 93 m² (1000 ft²))

0.2 m² (2 ft²)

CRD-C 509

(ASTM D 1752)

Preformed Sponge Rubber & Cork Expansion

Joint Fillers (per 93 m² (1000 ft²))

0.2 m² (2 ft²)

CRD-C 531

(ASTM D 2628)

Preformed Polychloroprene Elastomeric Joint Seals

If less than 2.5 cm (1 in) width

2.8 m (9 lin ft)

3.7 m (12 lin ft)

CRD-C 532

(ASTM D 2835)

Adhesive - Lubricant for Installation of Preformed

Joint Seals in Concrete Pavements

1 L (1 qt)

ASTM C 994

Preformed Expansion Joint Filler for Concrete,

Bituminous Type (per 93 m² (1000 ft²))

387 cm² (60 in²)

TT-P-0791B*

Putty, Linseed-Oil Type, for large bulk containers, composite sample from top, middle & bottom

For small lots of material, Federal Test Method Standard No. 141

1 L (1 qt)

Method 1021

Test

Description

Quantity Required

Joint Sealers

CRD-C 506

(TT-S-00227E)*

Elastomeric Type, Multi-component (Buildings &

Other Structures)(each component and lot)

(include sufficient primer)

8 L (8 qt)

CRD-C 526

(SS-S-200E)*

Elastomeric Polymer Type, Two-Component, Jet Fuel Resistant, Cold Applied (each component and lot) (include sufficient primer)

8 L (8 qt)

CRD-C 530

(SS-S-1401C)*

Hot Applied, for Concrete and Asphalt Pavements

(each lot)

8 L (8 qt)

SS-S-1614A*

Sealing Compound, Jet Fuel Resistant, Hot Applied,

One Component, for Portland Cement and Tar

Concrete Pavements (each lot)

8 L (8 qt)

Test

Description

Quantity Required

Soil and Soil-Cement Design

CRD-C 592

(ASTM D 558)

Moisture Density

3 kg (7 lb)

CRD-C 593

(ASTM D 559)

Wetting and Drying

3 kg (7 lb)

CRD-C 594

(ASTM D 560)

Freezing and Thawing

3 kg (7 lb)

--

Compressive and Tensile Splitting Strengths

As specified

Test

Description

Quantity Required

CRD-C 401

Water for Curing, Stain Test

3 L (3 qt)

CRD-C 402

CRD-C 403

CRD-C 404

CRD-C 405

Chemical Analysis

1 L (1 qt)

CRD-C 407

(ASTM C 932)

Test for Iron Bacteria

1 L (1 qt)

ASTM D 993

Test for Sulfate-Reducing Bacteria

1 L (1 qt)

Test

Description

Quantity Required

ASTM C 80

Water Retentivity of Masonry Mortar

160

ASTM C 476

Reinforced Masonry Mortar Mixture Proportioning

570

Common Brick

CRD-C 605

(ASTM C 55)

Concrete Building Brick (per lot)

3

ASTM C 62

Building Brick (Solid Masonry, Clay, or Shale)(per

50,000 bricks)

10

ASTM C 73

Calcium Silicate Face Brick (per 50,000 bricks)

10

ASTM C 216

Facing Brick (per 50,000 bricks)

10

Paving Bricks and Blocks

ASTM C 7

Paving Brick (per 50,000 bricks)

10

ASTM C 902

Pedestrian and Light Traffic Paving Brick (per 50,000 bricks)

25

--

Concrete Paving Block (per 50,000 blocks)

12

Refractory Bricks

CRD-C 20

(ASTM C 666)

Resistance to Freezing and Thawing

5

ASTM C 24

Pyrometric Cone Equivalent

5

ASTM C 113

Reheat Change of Refractory Bricks

3

ASTM C 133

Cold Crushing Strength and Modulus of Rupture of

Refractory Bricks and Shapes (min.)

5

ASTM C 134

Size and Bulk Density of Refractory Bricks and

Insulating Fire Brick

10

ASTM C 154

Warpage of Refractory Brick, or Deviation from a

Plane Surface

20

--

Coefficient of Thermal Expansion

5

--

For All Specification Tests

25

Test

Description

Quantity Required

Tile

ASTM C 34

Structural Clay Load-Bearing Wall Tile (each kiln or

lot)

5

ASTM C 56

Structural Clay Nonload-Bearing Tile (each kiln or

lot)

5

ASTM C 57

Structural Clay Floor Tile (each kiln or lot)

5

ASTM C 126

Ceramic Glazed Structural Clay Facing Tile, Facing

Brick, and Solid Masonry Units

(each additional 30,000 units)

1,000

10

Concrete Masonry

CRD-C 73

(ASTM C 426)

Dry Shrinkage of Concrete Block (half-face shells)

3

CRD-C 76

(ASTM C 427)

Moisture Condition by the Relative Humidity Method

As specified

CRD-C 606

(ASTM C 90)

Hollow Load-Bearing Units (10,000 units)

(10,000 units and greater)

10

20

CRD-C 607

(ASTM C 129)

Nonload-Bearing Units (10,000 units)

(10,000 units and greater)

10

20

CRD-C 608

(ASTM C 145)

Solid Load-Bearing Units (10,000 units)

(10,000 units and greater)

10

20

Masonry Mortars

CRD-C 602

(ASTM C 144)

Aggregate for Masonry Mortar

15 kg (33 lb)

CRD-C 609

(ASTM C 67)

Efflorescence adapted for Mortars

As Specified

CRD-C 618

(ASTM C 270)

Unit Masonry Mortar Mixture Proportioning

As Specified

ASTM C 80

Water Retentivity

As Specified

ASTM C 476

Reinforced Masonry Mortar Mixture Proportioning

As Specified

Test

Description

Quantity Required

Metals

CRD-C 501

(ASTM A 615)

Deformed and Plain Billet Steel Bars for

Concrete Reinforcement (each heat)

2

CRD-C 502

(ASTM A 616)

Rail Steel Deformed and Plain Bars for Concrete

Reinforcement (9071 kg (10 ton) lots)

2

CRD-C 503

(ASTM A 416)

Uncoated Seven-Wire Stress-Relieved Strand

for Prestressed Concrete (18142 kg (20 ton) lots)

2

CRD-C 510

(ASTM A 185)

Welded Steel Wire Fabric for Concrete

Reinforcement

0.1 m² (1.1 ft²)

CRD-C 519

(ASTM A 617)

Axle Steel Deformed Bars for Concrete

Reinforcement (9071 kg (10 ton) lots)

2

CRD-C 520

(ASTM A 82)

Cold-Drawn Steel Wire for Concrete Reinforcement

(9071 kg (10 ton) lots)

2

CRD-C 523

(ASTM A 421)

Uncoated Stress-Relieved Wire for Prestressed

Concrete (each 10 coils per lot)

1

CRD-C 524

(ASTM A 322)

Hot Rolled Alloy Steel Balls

As specified

CRD-C 562

(ASTM A 184)

Fabricated Steel Bar or Rod Mats for Concrete

Reinforcement (each 1000 mats)

2

ASTM A 370

Steel Products (Mechanical Tests)

As specified

--

Splices and Welds

As specified

--

Noncorrosive Wire Reinforcing Fabric

As specified

--

Certification of Threaded Restraining Rods (per lot)

3

--

All Other Types of Metals and Test Procedures

As specified

Test

Description

Quantity Required

Floor Tile

SS-T-312*

Asphalt, Rubber, Vinyl, & Vinyl Asbestos Tile (per

10,000 of each type, color, or size)

20

MMA-A-110*

Adhesive, Asphalt, Cutback Type

4 L (4 qt)

MMM-A-115*

Adhesive, Asphalt, Water Emulsion Type

4 L (4 qt)

ASTM C 57

Clay Tile (each kiln or each 90718 kg (100 ton))

5

--

All Other Tiles and Adhesives

As specified

Oils

--

Lubricating Oil

As specified

--

Insulating (Transformer) Oil

As specified

Roofing Material

SS-R-501*

SS-R-630*

HH-R-595*

Roofing Felts

As specified

SS-S-298*

SS-S-300*

Shingles

As specified

ASTM C 312

(SS-A-701)*

ASTM D 449

(SS A 666)*

Asphalt

1 L (1 qt)

R-P-381*

Pitch and Coal Tar

1 L (1 qt)

Test

Description

Quantity Required

Other Materials

CRD-C 300

Curing Compound

As specified

CRD-C 316

(TT-T-291E)*

Solvent

2 L (2 qt)

CRD-C 532

(ASTM D 2835)

Lubricant for Preformed Pavement Seals (each lot)

1 L (1 qt)

CRD-C 590

MMM-G-650a*

CRD-C 591

MMM-B-350B*

Epoxy Resin Binder or Grout (each component)

2 L (2 qt)

CRD-C 621

Non-shrink Grout (minimum of 1 package)

0.03 m³ (1 ft³)

ASTM C 881

Epoxy-Resin Base Bonding Systems (each component)

2 L (2 qt)

--

Mineralogy and Microstructure of Soils,

Clays, Site Rocks, and Masonry Units

As specified